Complied matters
The washing machine used by customer in past days had low washing performance and took long time to meet required standard. We confirmed various conditions such as brush material, rotating speed and contact angle etc. with test and discussed. Based on the results, we achieved to make machine with greatly reduced tact time. In addition, we took account of maintenance function for example easy to change brush as consumables. In the result, operating rate was also improved.
Technology used
-
Washing
We have substantial experience from low-cost standard spec washing machine using brush and two fluids to completely custom-built high functional washing machine. The combination with other production process such as chamfering process of substrate and transportation process etc. are also possible.
See machines using this technology > -
The Machine on Washing
-
Twin fluid washing machine (catalog sales)
Washing machine which has the characteristics of machine cost and running cost reduction.
-
Brush washing machine
Machine to take out engine parts aligned on pallet one by one automatically and remove contamination generated in processing by special brush pouring wash solution in washing bath. After washing, blow solution and discharge parts to designated place of pallet.
-
-
Sequencer control
Respond to almost all PLC such as Mitsubishi, Omron, Keyence and Siemens etc. Also available for traceability, MES and safety PLC.
See machines using this technology > -
The Machine on Sequencer control
-
Compact Sensor Assembly Machine
Machine to assemble compact sensors with a size of a few millimeters
-
Twin fluid washing machine (catalog sales)
Washing machine which has the characteristics of machine cost and running cost reduction.
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Automobile plumbing components
Assembly machine for automobile parts. Machine to assemble resin parts including laser welding, check air tightness and flow volume.
-
Brush washing machine
Machine to take out engine parts aligned on pallet one by one automatically and remove contamination generated in processing by special brush pouring wash solution in washing bath. After washing, blow solution and discharge parts to designated place of pallet.
-
Seal material coating applicator (with course correcting function)
Machine to have correct seal material application imperviously to work variability by correction of application trajectory with measuring work shape. High performance application machine including material heating function, pneumatic transportation of high viscosity material, UV curing process, inspection process after application and data collection function.
-
Piston ring groove processing machine
Machine to groove for "piston ring" for fixing to piston used in internal combustion.
-
Transfer machine (processing machine for several processes)
Machine to process 5 processes such as boring, grooving and C side processing etc. with transporting work on a separate station in order. Some processes employ CNC control to get high accuracy processing.
-
Large size glass carrier machine
Loading machine to take out thin glass with size of 2000mm square or more from storage and transport.
-
-
Wiring technology
We wire in consideration of visual effects and stable use for the long term. We give importance to minimalize stress at operation and selection of the most suitable wiring materials.
See machines using this technology > -
The Machine on Wiring technology
-
Electrode cutting machine for lithium-ion secondary batteries etc.
Machine to cut positive electrode or negative electrode of lithium-ion batteries etc. from original roll to batteries size.
-
Laminating machine for lithium-ion secondary batteries etc.
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy and high speed.
-
TAB ultrasonic welder for lithium-ion secondary batteries etc.
Machine to weld collecting tab to electrodes of lithium-ion batteries, etc.
-
Laminate forming machine for lithium-ion secondary batteries etc.
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries, etc.
-
Compact Sensor Assembly Machine
Machine to assemble compact sensors with a size of a few millimeters
-
Jerry-roll (JR) insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert jerry-roll and bottom insulator to external can of cylindrical lithium-ion batteries etc.
-
Swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to swage external can of cylindrical lithium-ion batteries etc.
-
Negative-electrode welding, CP insertion and TP insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert center pin after welding negative electrode in manufacturing process of lithium-ion batteries, etc. and to insert punched out top insulator for later process.
-
Injection machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in the manufacturing process of items such as lithium-ion batteries, etc. Developed to shorten the impregnation time by application of pressure in addition to vacuum immersion.
-
Electrolytic injection machine for lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in manufacturing process such as lithium-ion batteries, etc.
-
Sealing port laser-welding machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert sealing port and positive electrode tab to external can after welding by laser in the manufacturing process of items such as lithium-ion batteries, etc.
-
Sealing port swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to press and swage external can after being supplied the appropriate cell by insertion sealing port in the manufacturing process of lithium-ion batteries, etc.
-
Twin fluid washing machine (catalog sales)
Washing machine which has the characteristics of machine cost and running cost reduction.
-
Laminating machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy. Unlike the case of production machines, this machine has the priority of machine cost over processing speed.
-
Laminating machine with alignment function for film
Machine to apply heat laminate to each supplied film roll with heated roller. Normally, in case of laminating each film roll, apply only width direction by EPC etc, preventing position gap. However, it is able to adjust the position of not only the width direction but also the flow direction by controlling the amount of both feeds.
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Automobile plumbing components
Assembly machine for automobile parts. Machine to assemble resin parts including laser welding, check air tightness and flow volume.
-
Brush washing machine
Machine to take out engine parts aligned on pallet one by one automatically and remove contamination generated in processing by special brush pouring wash solution in washing bath. After washing, blow solution and discharge parts to designated place of pallet.
-
Seal material coating applicator (with course correcting function)
Machine to have correct seal material application imperviously to work variability by correction of application trajectory with measuring work shape. High performance application machine including material heating function, pneumatic transportation of high viscosity material, UV curing process, inspection process after application and data collection function.
-
Piston ring groove processing machine
Machine to groove for "piston ring" for fixing to piston used in internal combustion.
-
Transfer machine (processing machine for several processes)
Machine to process 5 processes such as boring, grooving and C side processing etc. with transporting work on a separate station in order. Some processes employ CNC control to get high accuracy processing.
-
Liquid crystal injection machine
Machine to inject liquid crystal into LCD one by one under vacuum after drying LCD input by magazine in a vacuum.
-
Laminating machine (zigzag system) for layered lithium-ion batteries etc.
Machine to layer electrode of layered lithium-ion batteries etc.. System to insert positive and negative electrode to separator folded in a zig-zag manner alternately.
-
18650 cylindrical lithium-ion batteries etc. assembly line
18650 cylindrical lithium-ion batteries assembly line, consistent line from insertion of jerry roll to crimp.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Measure for safety
The safety is of utmost importance. However, we must avoid great increasing in cost or reduction of workability otherwise merit of automatization is down by half. We have technology and experience to realize high safety without losing cost and workability as much as possible. Then we also respond to safety PLC.
See machines using this technology > -
The Machine on Measure for safety
-
Electrode cutting machine for lithium-ion secondary batteries etc.
Machine to cut positive electrode or negative electrode of lithium-ion batteries etc. from original roll to batteries size.
-
Laminating machine for lithium-ion secondary batteries etc.
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy and high speed.
-
TAB ultrasonic welder for lithium-ion secondary batteries etc.
Machine to weld collecting tab to electrodes of lithium-ion batteries, etc.
-
Laminate forming machine for lithium-ion secondary batteries etc.
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries, etc.
-
Probe Pin Processing Machine
Machine to give sharply-angled taper processing to cylindrical metallic material with diameter of 0.1mm or less.
-
Compact Sensor Assembly Machine
Machine to assemble compact sensors with a size of a few millimeters
-
Sheet to Roll Optical Film Adhering Machine
Machine to adhere 1 sq. meter sheet-shaped film or more with a clearance of 0.5mm to roll film with a width of 1meter or more continuously. Adhered roll films are cut to make sheet-shaped films and are stored.
-
Swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to swage external can of cylindrical lithium-ion batteries etc.
-
Negative-electrode welding, CP insertion and TP insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert center pin after welding negative electrode in manufacturing process of lithium-ion batteries, etc. and to insert punched out top insulator for later process.
-
Machine to place groove for cylindrical (18650) lithium-ion secondary batteries etc.
Used in the manufacturing process of items such as lithium-ion batteries, etc.
-
Injection machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in the manufacturing process of items such as lithium-ion batteries, etc. Developed to shorten the impregnation time by application of pressure in addition to vacuum immersion.
-
Electrolytic injection machine for lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in manufacturing process such as lithium-ion batteries, etc.
-
Sealing port laser-welding machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert sealing port and positive electrode tab to external can after welding by laser in the manufacturing process of items such as lithium-ion batteries, etc.
-
Sealing port swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to press and swage external can after being supplied the appropriate cell by insertion sealing port in the manufacturing process of lithium-ion batteries, etc.
-
Twin fluid washing machine (catalog sales)
Washing machine which has the characteristics of machine cost and running cost reduction.
-
Laminating machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy. Unlike the case of production machines, this machine has the priority of machine cost over processing speed.
-
Electrode cutting machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to cut positive or negative electrode of lithium-ion batteries etc. from original roll to batteries size. This machine requires manual operation and is intended for small-quantity production.
-
Laminate forming (cup forming) machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries etc. Machine including hand working for small-quantity production.
-
Laminate outer shape stamping machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to stamp outer shape of embossed laminate film to roll up electrodes for items such as lithium-ion batteries etc. and to make them the prescribed size. This machine requires manual operation and is intended for small-quantity production.
-
Laminate blank space cutting machine for lithium-ion secondary batteries etc. for small-quantity production
Jig to cut and remove margin section for accumulated gas of laminate cell of lithium-ion battery etc. Jig for manual operation and is intended for small-quantity production.
-
Laminating machine with alignment function for film
Machine to apply heat laminate to each supplied film roll with heated roller. Normally, in case of laminating each film roll, apply only width direction by EPC etc, preventing position gap. However, it is able to adjust the position of not only the width direction but also the flow direction by controlling the amount of both feeds.
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Automobile plumbing components
Assembly machine for automobile parts. Machine to assemble resin parts including laser welding, check air tightness and flow volume.
-
Brush washing machine
Machine to take out engine parts aligned on pallet one by one automatically and remove contamination generated in processing by special brush pouring wash solution in washing bath. After washing, blow solution and discharge parts to designated place of pallet.
-
Seal material coating applicator (with course correcting function)
Machine to have correct seal material application imperviously to work variability by correction of application trajectory with measuring work shape. High performance application machine including material heating function, pneumatic transportation of high viscosity material, UV curing process, inspection process after application and data collection function.
-
Piston ring groove processing machine
Machine to groove for "piston ring" for fixing to piston used in internal combustion.
-
Transfer machine (processing machine for several processes)
Machine to process 5 processes such as boring, grooving and C side processing etc. with transporting work on a separate station in order. Some processes employ CNC control to get high accuracy processing.
-
Large size glass carrier machine
Loading machine to take out thin glass with size of 2000mm square or more from storage and transport.
-
Liquid crystal injection machine
Machine to inject liquid crystal into LCD one by one under vacuum after drying LCD input by magazine in a vacuum.
-
-
Customer Specifications
We have the technology and experience to keep pace with the customer’s machine specifications and entering particulars such as TMS, DMS, Etc. We perform a review of the customer’s machine specifications with related personnel to avoid errors and omissions.
See machines using this technology > -
The Machine on Customer Specifications
-
Probe Pin Processing Machine
Machine to give sharply-angled taper processing to cylindrical metallic material with diameter of 0.1mm or less.
-
Compact Sensor Assembly Machine
Machine to assemble compact sensors with a size of a few millimeters
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Automobile plumbing components
Assembly machine for automobile parts. Machine to assemble resin parts including laser welding, check air tightness and flow volume.
-
Brush washing machine
Machine to take out engine parts aligned on pallet one by one automatically and remove contamination generated in processing by special brush pouring wash solution in washing bath. After washing, blow solution and discharge parts to designated place of pallet.
-
Seal material coating applicator (with course correcting function)
Machine to have correct seal material application imperviously to work variability by correction of application trajectory with measuring work shape. High performance application machine including material heating function, pneumatic transportation of high viscosity material, UV curing process, inspection process after application and data collection function.
-
Transfer machine (processing machine for several processes)
Machine to process 5 processes such as boring, grooving and C side processing etc. with transporting work on a separate station in order. Some processes employ CNC control to get high accuracy processing.
-