Complied matters
The customer installed similar machine in past times, but stability of releasing was very bad and automatic operating rate was extremely low. Therefore customer tried to manufacture using machine which was able to perform only automatic adhering. We designed new system which is able to get stable releasing and actualized using as machine. As a result, customer's productivity was improved as well as percent defective due to contamination was decreased because of no more manual work.
Technology used
-
Single Wafer (sheet shaped) Film Transportation
Technology to transport film which is thin and does not have body, without making a scratch or trace. Single wafer (sheet shaped) film easily generates static electricity compared with roll film, therefore it requires adequate countermeasures against static electricity. In the case of removal from stock area, countermeasures are required to avoid taking more than pieces of 2 film at a time. This technology has proven invaluable in the transport of sheet shaped film.
See machines using this technology > -
The Machine on Single Wafer (sheet shaped) Film Transportation
-
Electrode cutting machine for lithium-ion secondary batteries etc.
Machine to cut positive electrode or negative electrode of lithium-ion batteries etc. from original roll to batteries size.
-
Laminating machine for lithium-ion secondary batteries etc.
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy and high speed.
-
TAB ultrasonic welder for lithium-ion secondary batteries etc.
Machine to weld collecting tab to electrodes of lithium-ion batteries, etc.
-
Laminate forming machine for lithium-ion secondary batteries etc.
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries, etc.
-
Sheet to Roll Optical Film Adhering Machine
Machine to adhere 1 sq. meter sheet-shaped film or more with a clearance of 0.5mm to roll film with a width of 1meter or more continuously. Adhered roll films are cut to make sheet-shaped films and are stored.
-
Laminate three sided heat seal machine for lithium-ion secondary batteries etc.
Machine to seal laminate film which rolled up electrodes such as lithium-ion batteries, etc. with heater block.
-
Laminating machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy. Unlike the case of production machines, this machine has the priority of machine cost over processing speed.
-
Laminating machine (zigzag system) for layered lithium-ion batteries etc.
Machine to layer electrode of layered lithium-ion batteries etc.. System to insert positive and negative electrode to separator folded in a zig-zag manner alternately.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Mounting and base
Building a strong mounting and base for machinery is important for maintaining stability for the long term. A strong mounting and base also shortens the start-up time by minimizing accuracy deviation to transfer and transport mechanisms. Generally, we have eliminated the use of aluminum frames. We construct stable bases using thick square logs and a substantial base for the can manufacturing process. For various requirements, we do annealing and use a mount with additional accuracy.
See machines using this technology > -
The Machine on Mounting and base
-
Roll press for lithium-ion secondary batteries etc.
Machine to increase density of electrode material by pressing positive electrode or negative electrode of lithium-ion etc. with roller continuously.
-
Electrode cutting machine for lithium-ion secondary batteries etc.
Machine to cut positive electrode or negative electrode of lithium-ion batteries etc. from original roll to batteries size.
-
Laminating machine for lithium-ion secondary batteries etc.
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy and high speed.
-
TAB ultrasonic welder for lithium-ion secondary batteries etc.
Machine to weld collecting tab to electrodes of lithium-ion batteries, etc.
-
Laminate forming machine for lithium-ion secondary batteries etc.
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries, etc.
-
Probe Pin Processing Machine
Machine to give sharply-angled taper processing to cylindrical metallic material with diameter of 0.1mm or less.
-
Sheet to Roll Optical Film Adhering Machine
Machine to adhere 1 sq. meter sheet-shaped film or more with a clearance of 0.5mm to roll film with a width of 1meter or more continuously. Adhered roll films are cut to make sheet-shaped films and are stored.
-
Jerry-roll (JR) insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert jerry-roll and bottom insulator to external can of cylindrical lithium-ion batteries etc.
-
Swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to swage external can of cylindrical lithium-ion batteries etc.
-
Negative-electrode welding, CP insertion and TP insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert center pin after welding negative electrode in manufacturing process of lithium-ion batteries, etc. and to insert punched out top insulator for later process.
-
Machine to place groove for cylindrical (18650) lithium-ion secondary batteries etc.
Used in the manufacturing process of items such as lithium-ion batteries, etc.
-
Laminate three sided heat seal machine for lithium-ion secondary batteries etc.
Machine to seal laminate film which rolled up electrodes such as lithium-ion batteries, etc. with heater block.
-
Injection machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in the manufacturing process of items such as lithium-ion batteries, etc. Developed to shorten the impregnation time by application of pressure in addition to vacuum immersion.
-
Electrolytic injection machine for lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in manufacturing process such as lithium-ion batteries, etc.
-
Sealing port laser-welding machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert sealing port and positive electrode tab to external can after welding by laser in the manufacturing process of items such as lithium-ion batteries, etc.
-
Sealing port swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to press and swage external can after being supplied the appropriate cell by insertion sealing port in the manufacturing process of lithium-ion batteries, etc.
-
Laminating machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy. Unlike the case of production machines, this machine has the priority of machine cost over processing speed.
-
Laminating machine with alignment function for film
Machine to apply heat laminate to each supplied film roll with heated roller. Normally, in case of laminating each film roll, apply only width direction by EPC etc, preventing position gap. However, it is able to adjust the position of not only the width direction but also the flow direction by controlling the amount of both feeds.
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Automobile plumbing components
Assembly machine for automobile parts. Machine to assemble resin parts including laser welding, check air tightness and flow volume.
-
Seal material coating applicator (with course correcting function)
Machine to have correct seal material application imperviously to work variability by correction of application trajectory with measuring work shape. High performance application machine including material heating function, pneumatic transportation of high viscosity material, UV curing process, inspection process after application and data collection function.
-
Piston ring groove processing machine
Machine to groove for "piston ring" for fixing to piston used in internal combustion.
-
Transfer machine (processing machine for several processes)
Machine to process 5 processes such as boring, grooving and C side processing etc. with transporting work on a separate station in order. Some processes employ CNC control to get high accuracy processing.
-
Liquid crystal injection machine
Machine to inject liquid crystal into LCD one by one under vacuum after drying LCD input by magazine in a vacuum.
-
Laminating machine (zigzag system) for layered lithium-ion batteries etc.
Machine to layer electrode of layered lithium-ion batteries etc.. System to insert positive and negative electrode to separator folded in a zig-zag manner alternately.
-
18650 cylindrical lithium-ion batteries etc. assembly line
18650 cylindrical lithium-ion batteries assembly line, consistent line from insertion of jerry roll to crimp.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Adhesive Technology of Single Wafer (sheet shaped) Film
We have the technology to adhere single wafer (sheet shaped) film without making scratches or air bubbles. This mainly applies to the adhering of optical film for items such as flat displays and touch panels and the like. In adhering, roll laminate is generally desirable and responds to both cold and heat. Our machines can adhere film up to 700mm square. Positioning is accomplished by either mechanical or image processing means depending on the required level of accuracy. It is also possible to automate the peeling of the peel separator and protection film.
See machines using this technology > -
The Machine on Adhesive Technology of Single Wafer (sheet shaped) Film
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Film Stripping Technology
In the case of adhering single wafer (sheet shaped) film, peeling of the separator or protection film may be needed before adhering. We have developed a new film stripping technology which allows for the peeling of the separator and protection film adhered to the edge of the film of the same size without damaging the film. We have achieved a continuously stable operating rate by allowing for multiple peeling profiles to deal with variation in the peeling strength of a lot.
See machines using this technology > -
The Machine on Film Stripping Technology
-
Sheet to Roll Optical Film Adhering Machine
Machine to adhere 1 sq. meter sheet-shaped film or more with a clearance of 0.5mm to roll film with a width of 1meter or more continuously. Adhered roll films are cut to make sheet-shaped films and are stored.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Two up prevention of film
It is a technology that prevents the two up when loading one by one the film straight-loading state. The cause of the two up and mainly include “glue each other to adhere the end,” ” between the two eyes at the time of adsorption rise becomes a vacuum state,” ” static electricity is generated by peeling electrification.” Two up by weaving a mechanism to prevent these in the loading section and reduce to an absolute minimum. It also prevented from flowing to the post-process in the two take-up of any chance by also equipped with two up detection sensor.
See machines using this technology > -
The Machine on Two up prevention of film
-
Sheet to Roll Optical Film Adhering Machine
Machine to adhere 1 sq. meter sheet-shaped film or more with a clearance of 0.5mm to roll film with a width of 1meter or more continuously. Adhered roll films are cut to make sheet-shaped films and are stored.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Precise positioning
We have technology and experience to realize alignment system with high cost performance according to needs such as mechanism positioning and image processing. To maintain accuracy for the long term, we realize not only camera or positioning table but also precise positioning including design of mounting.
See machines using this technology > -
The Machine on Precise positioning
-
Electrode cutting machine for lithium-ion secondary batteries etc.
Machine to cut positive electrode or negative electrode of lithium-ion batteries etc. from original roll to batteries size.
-
Laminating machine for lithium-ion secondary batteries etc.
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy and high speed.
-
TAB ultrasonic welder for lithium-ion secondary batteries etc.
Machine to weld collecting tab to electrodes of lithium-ion batteries, etc.
-
Laminate forming machine for lithium-ion secondary batteries etc.
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries, etc.
-
Sheet to Roll Optical Film Adhering Machine
Machine to adhere 1 sq. meter sheet-shaped film or more with a clearance of 0.5mm to roll film with a width of 1meter or more continuously. Adhered roll films are cut to make sheet-shaped films and are stored.
-
Jerry-roll (JR) insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert jerry-roll and bottom insulator to external can of cylindrical lithium-ion batteries etc.
-
Swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to swage external can of cylindrical lithium-ion batteries etc.
-
Negative-electrode welding, CP insertion and TP insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert center pin after welding negative electrode in manufacturing process of lithium-ion batteries, etc. and to insert punched out top insulator for later process.
-
Machine to place groove for cylindrical (18650) lithium-ion secondary batteries etc.
Used in the manufacturing process of items such as lithium-ion batteries, etc.
-
Laminate three sided heat seal machine for lithium-ion secondary batteries etc.
Machine to seal laminate film which rolled up electrodes such as lithium-ion batteries, etc. with heater block.
-
Electrolytic injection machine for lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in manufacturing process such as lithium-ion batteries, etc.
-
Sealing port laser-welding machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert sealing port and positive electrode tab to external can after welding by laser in the manufacturing process of items such as lithium-ion batteries, etc.
-
Sealing port swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to press and swage external can after being supplied the appropriate cell by insertion sealing port in the manufacturing process of lithium-ion batteries, etc.
-
Laminating machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy. Unlike the case of production machines, this machine has the priority of machine cost over processing speed.
-
Laminating machine with alignment function for film
Machine to apply heat laminate to each supplied film roll with heated roller. Normally, in case of laminating each film roll, apply only width direction by EPC etc, preventing position gap. However, it is able to adjust the position of not only the width direction but also the flow direction by controlling the amount of both feeds.
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Transfer machine (processing machine for several processes)
Machine to process 5 processes such as boring, grooving and C side processing etc. with transporting work on a separate station in order. Some processes employ CNC control to get high accuracy processing.
-
Liquid crystal injection machine
Machine to inject liquid crystal into LCD one by one under vacuum after drying LCD input by magazine in a vacuum.
-
Laminating machine (zigzag system) for layered lithium-ion batteries etc.
Machine to layer electrode of layered lithium-ion batteries etc.. System to insert positive and negative electrode to separator folded in a zig-zag manner alternately.
-
18650 cylindrical lithium-ion batteries etc. assembly line
18650 cylindrical lithium-ion batteries assembly line, consistent line from insertion of jerry roll to crimp.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Image processing
We have various experience of image processing such as positioning, missing part and scratch etc. Respond to advanced image processing by the combination of the most suitable camera, lighting and processing device in response to shape of an object, accuracy and tact. Then it is also respond to continuous image processing of long object using licenser camera.
See machines using this technology > -
The Machine on Image processing
-
Electrode cutting machine for lithium-ion secondary batteries etc.
Machine to cut positive electrode or negative electrode of lithium-ion batteries etc. from original roll to batteries size.
-
Laminate forming machine for lithium-ion secondary batteries etc.
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries, etc.
-
Probe Pin Processing Machine
Machine to give sharply-angled taper processing to cylindrical metallic material with diameter of 0.1mm or less.
-
Compact Sensor Assembly Machine
Machine to assemble compact sensors with a size of a few millimeters
-
Jerry-roll (JR) insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert jerry-roll and bottom insulator to external can of cylindrical lithium-ion batteries etc.
-
Swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to swage external can of cylindrical lithium-ion batteries etc.
-
Negative-electrode welding, CP insertion and TP insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert center pin after welding negative electrode in manufacturing process of lithium-ion batteries, etc. and to insert punched out top insulator for later process.
-
Machine to place groove for cylindrical (18650) lithium-ion secondary batteries etc.
Used in the manufacturing process of items such as lithium-ion batteries, etc.
-
Laminate three sided heat seal machine for lithium-ion secondary batteries etc.
Machine to seal laminate film which rolled up electrodes such as lithium-ion batteries, etc. with heater block.
-
Electrolytic injection machine for lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in manufacturing process such as lithium-ion batteries, etc.
-
Sealing port laser-welding machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert sealing port and positive electrode tab to external can after welding by laser in the manufacturing process of items such as lithium-ion batteries, etc.
-
Sealing port swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to press and swage external can after being supplied the appropriate cell by insertion sealing port in the manufacturing process of lithium-ion batteries, etc.
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Liquid crystal injection machine
Machine to inject liquid crystal into LCD one by one under vacuum after drying LCD input by magazine in a vacuum.
-
18650 cylindrical lithium-ion batteries etc. assembly line
18650 cylindrical lithium-ion batteries assembly line, consistent line from insertion of jerry roll to crimp.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Improving of assembly accuracy
We have been working processing machines that high accuracy is required since the time of founding. For this reason, we have culture to assemble machine with improving accuracy like processing machine assembly for assembly other than processing machine, too. These machine assembled with improving accuracy is possible to maintain accuracy for long term.
See machines using this technology > -
The Machine on Improving of assembly accuracy
-
Roll press for lithium-ion secondary batteries etc.
Machine to increase density of electrode material by pressing positive electrode or negative electrode of lithium-ion etc. with roller continuously.
-
Electrode cutting machine for lithium-ion secondary batteries etc.
Machine to cut positive electrode or negative electrode of lithium-ion batteries etc. from original roll to batteries size.
-
TAB ultrasonic welder for lithium-ion secondary batteries etc.
Machine to weld collecting tab to electrodes of lithium-ion batteries, etc.
-
Laminate forming machine for lithium-ion secondary batteries etc.
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries, etc.
-
Compact Sensor Assembly Machine
Machine to assemble compact sensors with a size of a few millimeters
-
Jerry-roll (JR) insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert jerry-roll and bottom insulator to external can of cylindrical lithium-ion batteries etc.
-
Swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to swage external can of cylindrical lithium-ion batteries etc.
-
Negative-electrode welding, CP insertion and TP insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert center pin after welding negative electrode in manufacturing process of lithium-ion batteries, etc. and to insert punched out top insulator for later process.
-
Machine to place groove for cylindrical (18650) lithium-ion secondary batteries etc.
Used in the manufacturing process of items such as lithium-ion batteries, etc.
-
Laminate three sided heat seal machine for lithium-ion secondary batteries etc.
Machine to seal laminate film which rolled up electrodes such as lithium-ion batteries, etc. with heater block.
-
Injection machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in the manufacturing process of items such as lithium-ion batteries, etc. Developed to shorten the impregnation time by application of pressure in addition to vacuum immersion.
-
Electrolytic injection machine for lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in manufacturing process such as lithium-ion batteries, etc.
-
Sealing port laser-welding machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert sealing port and positive electrode tab to external can after welding by laser in the manufacturing process of items such as lithium-ion batteries, etc.
-
Laminating machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy. Unlike the case of production machines, this machine has the priority of machine cost over processing speed.
-
Electrode cutting machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to cut positive or negative electrode of lithium-ion batteries etc. from original roll to batteries size. This machine requires manual operation and is intended for small-quantity production.
-
Laminate forming (cup forming) machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries etc. Machine including hand working for small-quantity production.
-
Laminate outer shape stamping machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to stamp outer shape of embossed laminate film to roll up electrodes for items such as lithium-ion batteries etc. and to make them the prescribed size. This machine requires manual operation and is intended for small-quantity production.
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Automobile plumbing components
Assembly machine for automobile parts. Machine to assemble resin parts including laser welding, check air tightness and flow volume.
-
Seal material coating applicator (with course correcting function)
Machine to have correct seal material application imperviously to work variability by correction of application trajectory with measuring work shape. High performance application machine including material heating function, pneumatic transportation of high viscosity material, UV curing process, inspection process after application and data collection function.
-
Piston ring groove processing machine
Machine to groove for "piston ring" for fixing to piston used in internal combustion.
-
Transfer machine (processing machine for several processes)
Machine to process 5 processes such as boring, grooving and C side processing etc. with transporting work on a separate station in order. Some processes employ CNC control to get high accuracy processing.
-
Liquid crystal injection machine
Machine to inject liquid crystal into LCD one by one under vacuum after drying LCD input by magazine in a vacuum.
-
18650 cylindrical lithium-ion batteries etc. assembly line
18650 cylindrical lithium-ion batteries assembly line, consistent line from insertion of jerry roll to crimp.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Wiring technology
We wire in consideration of visual effects and stable use for the long term. We give importance to minimalize stress at operation and selection of the most suitable wiring materials.
See machines using this technology > -
The Machine on Wiring technology
-
Electrode cutting machine for lithium-ion secondary batteries etc.
Machine to cut positive electrode or negative electrode of lithium-ion batteries etc. from original roll to batteries size.
-
Laminating machine for lithium-ion secondary batteries etc.
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy and high speed.
-
TAB ultrasonic welder for lithium-ion secondary batteries etc.
Machine to weld collecting tab to electrodes of lithium-ion batteries, etc.
-
Laminate forming machine for lithium-ion secondary batteries etc.
Machine to get depression for placing electrodes by embossing laminate film to make packing for rolling up electrodes such as lithium-ion batteries, etc.
-
Compact Sensor Assembly Machine
Machine to assemble compact sensors with a size of a few millimeters
-
Jerry-roll (JR) insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert jerry-roll and bottom insulator to external can of cylindrical lithium-ion batteries etc.
-
Swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to swage external can of cylindrical lithium-ion batteries etc.
-
Negative-electrode welding, CP insertion and TP insertion machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert center pin after welding negative electrode in manufacturing process of lithium-ion batteries, etc. and to insert punched out top insulator for later process.
-
Injection machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in the manufacturing process of items such as lithium-ion batteries, etc. Developed to shorten the impregnation time by application of pressure in addition to vacuum immersion.
-
Electrolytic injection machine for lithium-ion secondary batteries etc.
Machine to inject electrolyte into cell in manufacturing process such as lithium-ion batteries, etc.
-
Sealing port laser-welding machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to insert sealing port and positive electrode tab to external can after welding by laser in the manufacturing process of items such as lithium-ion batteries, etc.
-
Sealing port swaging machine for cylindrical (18650) lithium-ion secondary batteries etc.
Machine to press and swage external can after being supplied the appropriate cell by insertion sealing port in the manufacturing process of lithium-ion batteries, etc.
-
Twin fluid washing machine (catalog sales)
Washing machine which has the characteristics of machine cost and running cost reduction.
-
Laminating machine for lithium-ion secondary batteries etc. for small-quantity production
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy. Unlike the case of production machines, this machine has the priority of machine cost over processing speed.
-
Laminating machine with alignment function for film
Machine to apply heat laminate to each supplied film roll with heated roller. Normally, in case of laminating each film roll, apply only width direction by EPC etc, preventing position gap. However, it is able to adjust the position of not only the width direction but also the flow direction by controlling the amount of both feeds.
-
Automobile security parts assembly
Machine to assemble more than 10 different parts in resin parts with diameter of approx. 50mm. The parts used for each product type are different, therefore machine has the function of selecting parts used automatically with change of type.
-
Automobile plumbing components
Assembly machine for automobile parts. Machine to assemble resin parts including laser welding, check air tightness and flow volume.
-
Brush washing machine
Machine to take out engine parts aligned on pallet one by one automatically and remove contamination generated in processing by special brush pouring wash solution in washing bath. After washing, blow solution and discharge parts to designated place of pallet.
-
Seal material coating applicator (with course correcting function)
Machine to have correct seal material application imperviously to work variability by correction of application trajectory with measuring work shape. High performance application machine including material heating function, pneumatic transportation of high viscosity material, UV curing process, inspection process after application and data collection function.
-
Piston ring groove processing machine
Machine to groove for "piston ring" for fixing to piston used in internal combustion.
-
Transfer machine (processing machine for several processes)
Machine to process 5 processes such as boring, grooving and C side processing etc. with transporting work on a separate station in order. Some processes employ CNC control to get high accuracy processing.
-
Liquid crystal injection machine
Machine to inject liquid crystal into LCD one by one under vacuum after drying LCD input by magazine in a vacuum.
-
Laminating machine (zigzag system) for layered lithium-ion batteries etc.
Machine to layer electrode of layered lithium-ion batteries etc.. System to insert positive and negative electrode to separator folded in a zig-zag manner alternately.
-
18650 cylindrical lithium-ion batteries etc. assembly line
18650 cylindrical lithium-ion batteries assembly line, consistent line from insertion of jerry roll to crimp.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Clean Technology
It is not just a matter of constructing machinery using clean production protocols. We take comprehensive measures to ensure the work is free of contamination and contaminant containment. In addition to design and manufacturing we pay careful attention to packing, transportation and installation as well. We have developed this system to allow us to maintain a necessary of cleanliness and reduce costs at the same time. This technology has been used for the production of liquid crystals, semiconductors and precision instruments with classes ranging from 10 to 10,000.
See machines using this technology > -
The Machine on Clean Technology
-
Compact Sensor Assembly Machine
Machine to assemble compact sensors with a size of a few millimeters
-
Chemical Injection Machine
Machine to inject chemicals into a special container without air bubbles quickly and accurately.
-
Sheet to Roll Optical Film Adhering Machine
Machine to adhere 1 sq. meter sheet-shaped film or more with a clearance of 0.5mm to roll film with a width of 1meter or more continuously. Adhered roll films are cut to make sheet-shaped films and are stored.
-
Laminating machine with alignment function for film
Machine to apply heat laminate to each supplied film roll with heated roller. Normally, in case of laminating each film roll, apply only width direction by EPC etc, preventing position gap. However, it is able to adjust the position of not only the width direction but also the flow direction by controlling the amount of both feeds.
-
Liquid crystal injection machine
Machine to inject liquid crystal into LCD one by one under vacuum after drying LCD input by magazine in a vacuum.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-
-
Countermeasures against Static Electricity (ESD)
Work has a damaging effect by static electricity and disturb stability of film transportation by static electricity. Therefore we need to have technology to stop static generation and remove generated static electricity. Almost all static electricity generated in machine is caused by peel electrification or frictional electrification. We design to make every effort to avoid these electrifications and construct effective neutralization method against generated static electricity by multiple measures of structure and neutralization apparatus.
See machines using this technology > -
The Machine on Countermeasures against Static Electricity (ESD)
-
Laminating machine for lithium-ion secondary batteries etc.
Machine to pile up positive electrode or negative electrode of lithium-ion batteries and separator in sequence with high accuracy and high speed.
-
Sheet to Roll Optical Film Adhering Machine
Machine to adhere 1 sq. meter sheet-shaped film or more with a clearance of 0.5mm to roll film with a width of 1meter or more continuously. Adhered roll films are cut to make sheet-shaped films and are stored.
-
Large size glass carrier machine
Loading machine to take out thin glass with size of 2000mm square or more from storage and transport.
-
Laminating machine (zigzag system) for layered lithium-ion batteries etc.
Machine to layer electrode of layered lithium-ion batteries etc.. System to insert positive and negative electrode to separator folded in a zig-zag manner alternately.
-
18650 cylindrical lithium-ion batteries etc. assembly line
18650 cylindrical lithium-ion batteries assembly line, consistent line from insertion of jerry roll to crimp.
-
Single wafer processing film adhering machine
Machine to apply two types of single wafer (sheet shaped) films automatically with a high degree of accuracy without scratches or air bubbles. Each film has a protection film and separator (mold releasing film), which are removed automatically while feeding.
-